Browse Temperature Sensor Kit shopping results from Amazon & compare with other online stores
Fit : 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 ENGINES Note:For the two red wires,please connect the long red wire to the fan and the short red wire to the battery. 1.Mount the relay under the hood in a convenient location as to the fan as possible. Notice:Don't use the teflon tape or thread compoud on the thermostat or adaptor.For proper operation,the thermostat must ground threough the threads to the engine and the engine must be ground. 2.Install thermostat into the head or intake manifold.Route the black wire to thermostat and cut to length.Crimp the red terminal onto the black wire and attach to thermostat. 3.Route and connect the red wire to the fan "+" terminal or power wire coming from the fan motor printed "to electric fan". 4.Mount the circuit breaker provided in a convenient location as close as possible to whichever power source(battery or large terminal on the starter solenoid)you are using for the fan relay. 5.Neatly route the red wire from the relay to one side circuit breaker installed in step 5. Cut to length and install using a small yellow ring terminal .With another small yellow ring terminal take the remaining red wire and ...
INTRODUCTION If you are familiar with our product, you will find there is waterproof temperature sensor named DS18B20. This waterproof temperature sensor kit is using the same probe--DS18B20 probe AS. It contains a probe with a resister module. So it is easy to connect on the Arduino board. The DS18B20 temperature sensor provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor. Compatible with 3.0-5.5V systems. SPECIFICATION Operating voltage: 3.0~ 5.5V ±0.5°C Accuracy from -10°C to +85°C Usable temperature range: -55 to 125°C (-67°F to +257°F) 9 to 12 bit selectable resolution Uses 1-Wire interface- requires only one digital pin for communication Unique 64 bit ID burned into chip Multiple sensors can share one pin Temperature-limit alarm system Query time is less than 750ms 3 wires interface: - Type A Red wire - VCC Black wire - GND Yellow wire - DATA - Type B Red wire - VCC Yellow wire - GND Green wire - DATA Stainless steel tube 6mm diameter by 35mm (1.34") long Cable diameter: 4mm (0.16") Length: 90cm (35.43") SHIPPING LIST Waterproof DS18B20 Digital temperature sensor (DFR0198) x1 Terminal sensor adapter (DFR0055) x1 Digital s...
OWC In-line Digital Thermal Sensor for iMac 2011 Hard Drive Upgrade. OWC DIY Kit for all Apple iMac 2011 Models for replacing the main hard drive. Includes all cables necessary for installation. Hard drive and tools sold separately. Eliminate fan noise and maintain correct system fan control when upgrading your 2011 iMac. The only iMac HDD upgrade option on the market certified to pass the Apple Hardware Test. Fixes firmware incompatibility issues with third party hard drives. Engineered in-house and backed by OWC's award-winning customer support. Improve Performance and Capacity. Upgrade Your iMac with Confidence. OWC's in-line solution is the only hardware digital thermal sensor on the market allowing a third-party SATA drive to be installed in your iMac. A convenient, plug-and-play cable, the In-line Digital Thermal Sensor eliminates fan noise and maintains proper system fan control through the iMac's System Management Controller. This innovative device is designed specifically for the iMac, requires no software hacks and ensures compatibility with Apple's built-in diagnostic processes. Note: Before attempting to perform this installation, please watch the OWC Install Video, corresponding to your machine, in its entirety to determine your ability to perform this complex upgr...
Specification: Voltage: 12V DC Material: Plastic and Metal Package Box Size: 13 x 9 x 7cm (L x W x H) Cable Length: approx.165cm Quantity: Pack of One Set Package include: 1× Fan Temperature Switch (Includes a brass adapter to install the sending unit wires, relay switch, circut breaker, terminals and mounting screws.)
This temperature sensor kit is designed to use with Hayward salt chlorine generators and also compatible with Pro Logic automation models PL-PS-8 , PL-PS-8-V. 10K thermistor. Includes 15-Feet cable. Weight 6 pounds.
ALL ITEMS PICTURED ABOVE INCLUDED: 50 AMP Relay 48" of Wiring 12-18 GAUGE Temperature Sensor Circuit Breaker Assorted Connectors And Terminals COMES ON AT 200 Degrees AND TURNS OFF AT 185 Degrees FITS 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 ENGINES THIS KIT IS A MUST HAVE WHEN USING AN ELECTRIC FAN IN YOUR HOT ROD OR STREET ROD FITS MOST HOT RODS AND CLASSICS ENGINES INCLUDING GM (CHEVY, GMC, OLDS, CADILLAC, PONTIAC, BUICK, FORD, & MOPAR (CHRYSLER, DODGE, PLYMOUTH) PLEASE MEASURE TO MAKE SURE THIS IS THE RIGHT SIZE AS 7" 10"12"14"16" ELECTRIC FANS
Free Gift 1 x MQ-2 Gas Sensor Module some Resistor 1x CD Package included: 1 x Soil module 1 x Infrared sensor receiver module 1 x Laser head sensor module 1 x Temperature and humidity sensor module 1 x Infrared emission sensor module 1 x 5V relay module 1 x Gyro Module 1 x ARDUINO finger detect heartbeat module 1 x Microphone sensitivity sensor module 1 x Metal touch sensor module 1 x Flame sensor module 1 x 3-color LED module 1 x Hunt sensor module 1 x Linear magnetic Hall sensors 1 x Rotary encoder modules 1 x Active buzzer module 1 x Small passive buzzer module 1 x Digital temperature sensor module 1 x Tilt switch module 1 x Analogy Holzer magnetic sensor 1 x Ultrasonic module 1 x Hall magnetic sensor module 1 x RGB LED SMD module 1 x Arduino Mini Reed module 1 x Bicolor LED common cathode module 3MM 1 x Smart car avoid obstacle sensor infrared sensor photoelectric switch 1 x Key switch module 1 x Photoresistor module 1 x Breadboard power module 1 x ARDUINO hit sensor module 1 x Temperature sensor module 1 x Vibration switch module 1 x Microphone sound sensor module 1 x Large reed module 1 x Two-color LED module 1 x Optical breaking module 1 x Temperature sensor module 1 x MP1584EN buck module 1 x SD card reader module 1 x Arduino PS2 Joystick game controller module1 x Autom...
About Weker Weker is one of the best automotive aftermarket parts provider. We are dedicated to provide the best product,and the best overall shopping experience.Our goal is to make car maintenance affordable. Please see compatibility chart. Fits: 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 ENGINES Part Notifications: 1.For the two red wires, please connect the long red wire to the fan and the short red wire to the battery. 2.Mount the relay under the hood in a convenient location as to the fan as possible Notice: Don't use the Teflon tape or thread compound on the thermostat or adaptor. For proper operation, the thermostat must ground through the threads to the engine and the engine must be ground. 3.Install thermostat into the head or intake manifold. Route the black wire to thermostat and cut to length. Crimp the red terminal onto the black wire and attach to thermostat. 4.Route and connect the red wire to the fan "+" terminal or power wire coming from the fan motor printed "to electric fan". 5.Mount the circuit breaker provided in a convenient location as close as possible to whichever power source(battery or large terminal on the starter sol...
This is an excellent collection of sensors and components to use with Arduino and Raspberry Pi. It was specially designed for smart home. It comes with 16 sensor modules and female to female jumper wires, everything was properly identified and individually packed in plastic box. No matter where you are,the smart home sensor kit combined with arduino or Raspberry let you to control, monitor and secure your home. We provide detailed instruction containing 16 projects with description and sample code. Please go to KOOKYE office website: http://kookye.com/?p=1573 Packing list: 1x Voltage sensor 1x MQ2 smoke sensor 1x MQ5 coalgas sensor 1x MQ7 carbon monoxide sensor 1x DS18B20 temperature sensor 1x DHT11 temperature humidity sensor 1x Flame detection sensor 1x Water level sensor module 1x Digital touch sensor module 1x Vibration sensor module 1x Sound sensor module 1x Photosensitive sensor module 1x Passive buzzer module 1x BMP180 digital air pressure sensor 1x HC-SR501 infrared sensor module 1x Two-way relay module 1x jumper wires 20cm
Specification and Size:
1.Front panel size75(L)×34.5(W)mm;
4.sensor length2minclude the probe.
5.Measure range: -50°+99°C
6.Mounting size: 71*29mm
7.Auto switch between refrigerating and heating
8.Retrun difference value
1. Temperature measuring range: -50°~99°C;
2. Resolution: 0.1°C;
3. Accuracy: ±1°C (-50~70°C);
4. Sensor error delay: 1 minute
5. Power supply: 110VAC±10%, 50/60Hz;
6. Power consumption: less than 3W;
7. Sensor: NTC sensor (1PC);
8. Relay contact capacity: Cool 10A/250VAC;Heat 10A/250VAC;
9. Ambient temperature: 0~60°C;
10. Storage temperature: -30~75°C;
11. Relative humidity: 20%~85% (No condensate).
1 x Mini Digital Temperature Controller Thermostat Aquarium
1 x Temperature sensor probe with 2M cable
1 x Instruction Manual
Don't satisfied with search results? Try to more related search from users who also looking for Temperature Sensor Kit: Taupe Makeup, Rec Navigation, Swisher Sweets Cigarillos Box, Pictures New York City Skyline, Titanium Plate Head.